Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Flushing: What to Know First
Olympia Chimney liner replacement and rebuild work in Flushing typically runs $2,900 to $7,600 depending on whether we’re relining the flue or rebuilding brick from the roofline up. We’re an independent Olympia Chimney service provider, not a manufacturer-authorized shop, which means we quote the repair based on what the camera shows, not what a warranty department will approve. Most liner jobs take one day; a full rebuild runs three to five. If you own an Olympia system in Flushing and you’re seeing flue deterioration, call (516) 240-9191 and we’ll get a camera down the chimney before anyone quotes a dollar.
How Olympia Chimney Products Fail - and How We Fix Them
We service Olympia Chimney products across Flushing, from the older masonry-connected systems in Colonial and Ranch homes near Kissena Park to newer pre-fab installations in attached housing off Northern Boulevard. Here’s what we actually find when the camera goes down:
- Olympia stainless rigid liners develop seam separation at the flue offsets. In Flushing’s freeze-thaw winters, the expansion and contraction at the elbows where the liner jogs around a smoke shelf pulls the seams apart. We see this on Olympia’s 304-series rigid liner in homes with exterior chimneys on the north side of the house. The fix is usually a flexible liner conversion, which eliminates the offset seams entirely.
- Olympia flexible liner kinking behind the damper frame. On Olympia’s flexible liner installations from the mid-2010s, installers frequently left too much slack in the liner above the damper. Over time, thermal cycling causes the slack to fold and kink, which restricts draft and traps creosote. We remove the kinked section, re-pull the liner with correct tension, and secure it to a new top plate instead of the damper.
- The clay tile flues Olympia components connect to are the real failure point, not the Olympia parts. This comes up constantly in Flushing’s pre-war housing stock near Flushing Town Hall. The Olympia stainless connector boot at the base of the flue is often in decent shape, but the original terra cotta tiles above it are spalling, cracked, or shifted. The camera shows the tile damage, and the fix is a full reline with an insulated stainless system that isolates the flue from the masonry.
- Olympia chase covers rusting through on pre-fabricated systems. On Olympia’s factory-built chimney systems installed in Flushing townhouses, the chase cover is a galvanized metal top that takes direct rain, snow, and salt air off the Long Island Sound. Once it rusts through, water drops straight onto the firebox and the liner connection. We replace the chase cover and inspect the liner joint beneath it, because that joint is usually the next thing to go.
- Condensation corrosion at the base of Olympia gas liners. On homes where Olympia’s AL29-4C gas vent liner was installed for high-efficiency furnace retrofits, we find acidic condensation pooling at the liner base when the pitch of the horizontal connector was set wrong. The liner wall thins from the inside out, which is why the camera inspection matters - the outer surface looks fine right up until it isn’t. We replace the corroded section and correct the connector pitch so condensation drains back to the appliance instead of sitting in the liner.
Our Olympia Chimney Chimney Liner & Rebuild Process
Every Olympia job in Flushing follows the same sequence, because skipping steps is how liner work gets missed:
- 1
Scheduled camera-scan inspection. We run a Level 2 camera inspection per NFPA 211. You see the footage as it happens, not an edited version later. We’re looking at the Olympia liner, the tile behind it, the smoke chamber, and the crown.
- 2
Written findings with photos. We hand you a written condition report with still images pulled from the camera footage. This is Clause 4 of the Haven Standard, and it’s been our default since 2009. If the liner’s thinned to 28-gauge from 24-gauge at the mid-flue, the report says that in numbers, not adjectives.
- 3
Written price, written scope, written warranty. We list whether we’re using OEM Olympia components or a quality aftermarket liner like DuraFlex. The warranty on the repair is written, not verbal. No work starts until you approve what’s on paper.
- 4
The repair or rebuild itself. Liner replacements are typically done in one day. Full rebuilds mean staging materials, protecting the roof, and working the masonry in lifts. Corrine Halstead reviews the job notes by hand before she signs off on the completion report.
- 5
Post-work camera verification. After the new liner is in or the rebuild is done, the camera goes back down to confirm the install. You get the post-work footage for your records.
- 6
Documented photo record and Done Right Promise. You walk away with the full photo archive of the job. If something isn’t right within 365 days, we make it right. That promise is stamped on the job paperwork, not buried in fine print.
BeforeAfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Flushing
Here’s where prices actually land for Olympia work in Flushing, based on what we’ve quoted and completed:
- Stainless steel liner replacement (flexible, single flue): $2,900 - $4,400
- Insulated liner system (exterior chimney, freeze-thaw zone): $4,200 - $5,800
- Partial rebuild (crown, top courses, flue tile replacement): $3,500 - $5,600
- Full chimney rebuild from the roofline up: $5,400 - $7,600
- Olympia chase cover replacement plus liner inspection and joint repair: $900 - $1,600
What moves the price: the flue height, whether the chimney is on an exterior wall or through the center of the house, the condition of the surrounding masonry, and whether we’re pulling a permit. Flushing building code requires a permit for full rebuilds, and we handle the paperwork. Call (516) 240-9191 for a written quote. The estimate is free, and the price on paper is the price you pay. No “call for quote” games - the quote is the point.
Why Flushing Homeowners Call Level Two Chimney Flushing for Olympia Chimney Work
We made camera-scan documentation the default in 2009, years before insurers or regulators asked for it. That practice became Clause 4 of the Haven Standard, and it’s why the price you approve matches the flue you actually have. Every one of the 38,000-plus chimneys we’ve inspected and cleaned since 2009 has left behind a written price before work and a documented record after it. Our techs are background-checked and uniformed, they carry their license number on them, and you get a text when they’re on the way. When an Olympia liner isn’t available or an OEM part is backordered, we quote quality aftermarket options from DuraFlex, HeatShield, or Gelco through Haven’s buying network specifically to keep the price honest. And if you’ve got a written estimate from another Flushing chimney company, bring it to us. A free second opinion is always available.
FAQs
It depends on what got installed and how the warranty was registered, but an independent repair using listed, code-compliant components does not automatically void an Olympia Chimney warranty. We’re not an Olympia-authorized service provider, so we can’t speak for their warranty department, but we’ve seen warranty claims survive independent liner work. What matters is that the repair is done to NFPA 211 standards and documented. We photograph everything and hand you the record, so if a warranty question ever comes up, you’ve got the evidence. Call (516) 240-9191 if you want us to look at what you have.
The camera shows it. Symptoms like smoke backing up into the living room, a sulfur smell in the house, or flaking rust on the firebox floor can mean liner failure, but the only way to confirm is a camera scan of the flue. We’ve found Olympia liners that looked fine from the fireplace side and were completely separated at the mid-flue on the camera. The camera doesn’t negotiate - it just shows you what’s there. If the liner’s intact and the issue is something else, we’ll tell you that too, with footage to prove it.
Sectional repairs are possible in some cases, but for stainless liners with seam separation or kinking, a full reline is usually the honest fix. Patching one section of a liner that’s failed at the offset often means the rest of it is on borrowed time, and you’d be paying for labor twice. For clay tile flues connected to Olympia components, we can sometimes replace only the damaged tiles if the rest of the flue shows no cracking or shifting on camera. The written quote will list both options with prices when they’re both viable.
We schedule camera-scan inspections throughout the week, and we answer calls with a live person 24/7 - no voicemail, no web form. Liner replacement jobs are usually completed in a day once you approve the written scope. Full rebuilds take three to five days depending on weather and masonry access. If you call (516) 240-9191, we’ll give you a straight answer on scheduling for your specific situation, not a generic window.
If the camera shows the liner has failed or is close to it, yes - and having the photo documentation from the inspection makes the work defensible to a buyer’s home inspector. Flushing buyers in the 2015-2025 purchase wave tend to be thorough; they’re hiring their own inspectors, and a failed liner shows up on home inspection reports as a flagged safety item. The documentation we hand you after a liner replacement gives the buyer’s inspector something concrete to verify. If the liner’s actually fine on camera, we’ll write that down too, and that’s equally useful at the negotiation table.
Written by Corrine Halstead, Owner, Level Two Chimney Flushing at Level Two Chimney Flushing, serving Flushing and nearby areas.