Famco Chimney Liner & Rebuild Nationwide

Famco Chimney Liner & Rebuild in Flushing: What to Know First

Famco chimney liner replacement and full rebuild work in Flushing typically runs $2,200 to $5,400 depending on flue height, liner material, and whether the existing masonry can be saved. We’re an independent Famco service provider, not a Famco dealer, which means we quote you the repair that matches what the camera shows, not what a manufacturer program dictates. Most Famco liner jobs in Flushing are done in one day once parts are on hand. This page is for homeowners in Flushing whose Famco chimney has a failed or failing liner, a cracked crown, spalling brick, or a fireplace that smokes back into the room. If you want a written price before any work starts, call (516) 240-9191.

Call (516) 240-9191

Key takeaways:

• We service Famco chimney liners and full rebuilds across Flushing, including Murray Hill, Auburndale, and the Town Hall district.
• Every estimate is written, not spoken. You get the number before we touch anything.
• Camera inspection is included on every visit. You see what we see.
• Parts come from Famco directly or from DuraFlex, HeatShield, and Gelco when a better-fit option exists.

How Famco Products Fail - and How We Fix Them

Famco makes solid stainless steel liners, but like any chimney component exposed to Flushing’s freeze-thaw cycles and coastal humidity, certain failure patterns show up again and again. Here’s what we find in Flushing homes:

• Famco 316L flexible liners: pitting near the bottom three feet. Flushing’s older attached homes, especially colonials near Bowne Street, draw combustion air from damp basements. That moisture condenses inside the liner’s lower section and sits there between fires. Over five to eight years, we see pitting and pinholes at the bottom. The fix is a partial liner replacement, not a full one, if the upper flue is intact.
• Famco rigid liner sections separating at the joints. Rigid liner is great until a chimney shifts. Flushing’s clay soil expands and contracts, and we see homes near Flushing Meadows where the chimney has moved just enough to pull rigid sections apart at the seams. Exhaust leaks into the chimney cavity instead of going up. We repair by re-aligning and re-clamping the joints, or replacing failed sections with flexible liner where the flue path isn’t straight.
• Smoke chamber breakdown above a Famco liner. The liner does its job, but the smoke chamber above it gets ignored for decades. We open the chamber, find deteriorated mortar and corbeled brick, and that’s where the drafting problems begin. We parge the smoke chamber with a refractory mortar and re-connect the liner correctly.
• Famco crown kits cracking at the liner entry point. The crown is the concrete cap on top of the chimney. Famco crown kits work, but the seal around the liner’s top plate fails when the crown shifts. Rain gets in, runs down the outside of the liner, and freezes. We rebuild the crown, install a proper flue cap, and re-seal the liner top plate.
• Installation errors from previous contractors. We’ve pulled Famco liners in Flushing that were never insulated, never properly connected to the appliance, or terminated below the flue tile. The liner material was fine; the installation wasn’t. Our rebuild fixes the connection, insulation, and termination so the liner can actually do its job.

Our Famco Chimney Liner & Rebuild Process

A Famco liner replacement or rebuild in Flushing follows the same documented process on every job. No shortcuts, no verbal changes, no surprise add-ons. Here’s what happens:

1. 1
   Initial call and scheduling. You call (516) 240-9191. A live person answers, asks about your chimney, and schedules a visit. No voicemail, no web form.
2. 2
   Camera inspection. Corrine or a Level Two technician runs a camera down the flue before quoting anything. You watch the footage as it’s being recorded. We identify the liner condition, the smoke chamber, the crown, and the flue tile. You get a copy of the photo record.
3. 3
   Written quote with parts specified. We write the price, the scope, and the warranty. The quote names the liner material: Famco, DuraFlex, HeatShield, or Gelco. If aftermarket is a better fit, we say why in writing. If OEM Famco is the right call, we quote it, including current lead times.
4. 4
   The liner work or rebuild. We remove the failed liner or damaged masonry, prep the flue, install the new liner, and re-seal the crown. If a rebuild is needed, we do it in the same visit where structurally possible. Work is done by background-checked, uniformed technicians.
5. 5
   Post-installation test and documentation. We test the draft, run the camera again, and hand you a written post-job report with before and after photos, parts used, and warranty terms.
6. 6
   The 365-Day Done Right Promise. If it’s not done right, we make it right. That’s stamped on every job under the Haven Standard. Not as a slogan, as a written warranty.

Before

After

What Famco Chimney Liner & Rebuild Costs in Flushing

Here’s what we’ve quoted on Famco jobs in Flushing over the past several seasons:

• Famco 316L flexible liner replacement, single flue, two-story home: $2,200 to $3,800. Includes removal, new liner, top plate, new cap, and insulation where needed.
• Partial rebuild (crown, top five courses of brick, liner re-seal): $1,800 to $3,200. Price moves based on brick matching and roof access. Flushing homes with steep slate roofs run higher.
• Full chimney rebuild from the roofline up: $4,000 to $7,500. Includes new liner, smoke chamber parging, new crown, new cap, and brick. Flushing townhouse work, where neighbor walls abut, adds scaffolding complexity.
• Smoke chamber parging and liner reconnection: $900 to $1,600 when the liner itself is sound.

What moves the price in Flushing: roof pitch, access from neighboring structures, whether you need a full vs. partial rebuild, and whether the existing liner can be removed in one piece or needs to be cut out in sections. Call (516) 240-9191 for a written estimate. We don’t quote over the phone without a camera inspection, but the estimate itself is free.

Why Flushing Homeowners Call Level Two Chimney Flushing for Famco Work

We’ve inspected and cleaned more than 38,000 chimneys since 2009, and every one of them had a written price before work started and a documented record when it was done. That’s not a marketing line; it’s what Clause 4 of the Haven Standard requires, and we’ve been doing it before anyone asked us to. Corrine Halstead grew up in Queens and has been doing chimney work across the borough for the better part of two decades, including older attached homes near the Flushing Town Hall district. She’ll show you the camera footage before she quotes anything. The camera doesn’t negotiate, it just shows you what’s there. We also stock and install DuraFlex, HeatShield, and Gelco liners, so if a Famco part is backordered or the OEM markup doesn’t make sense for your job, we can offer an honest alternative in writing. You get a real warranty, a real photo record, and a real person on the phone 24/7. That’s the whole offer.

FAQs