Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Flushing Owner’s Guide

An Olympia Chimney flue liner replacement in Flushing typically runs $2,400 to $4,800 installed, depending on liner diameter, flue height, and whether we’re relining an existing chimney or replacing a failed liner in place. We stock Olympia Chimney-compatible liners on the truck in the most common Flushing sizes: 5.5″, 6″, and 8″ diameters, in both 316L and 904L alloy. Most replacements are completed in one visit, usually four to six hours once we’re on the roof and the old liner comes out.

Call (516) 240-9191

The way most Flushing homeowners discover their Olympia liner has failed isn’t dramatic. It’s a slow thing. The fireplace starts smoking back into the living room on windy days. The damper won’t hold position. Or a sweep from another company runs a camera up the flue and hands over photos showing cracks, rust-through, or a liner that’s separated at the seam. That’s usually the first time anyone has looked at that liner since the house was built. A lot of the attached brick homes in the Flushing Town Hall district have original liners from the 1950s and 60s, and clay tile liners from that era are at the end of their service life. We see it constantly.

The camera doesn’t negotiate - it just shows you what’s there. Corrine Halstead has run a camera up more Flushing flues than she can count, and what the footage shows dictates what we quote. Nothing more.

Key takeaways:

• We install Olympia Chimney-compatible stainless flue liners, insulated and sized to your existing flue dimensions.
• Installed price range in Flushing: $2,400-$4,800, written and itemized before work starts.
• We’re an independent installer - we stock Olympia Chimney components alongside DuraFlex, HeatShield, and Gelco.
• Every replacement includes a camera-scan record of the new liner, per Haven Standard Clause 4.

Which Olympia Chimney Models This Applies To

Olympia Chimney has sold liners and venting components for decades, and the model naming isn’t always stamped on the part. Most Flushing homes with an Olympia liner have either the Olympia Pro Series or the Olympia Ventinox line, though we also see plenty of unbranded Olympia-manufactured liners that were installed by builders in the 1980s and 90s. If you can’t find a label, two measurements matter: the inner diameter (ID), measured across the opening, and the overall length from the appliance outlet to the chimney crown.

The gotcha with Olympia specifically: their 5.5″ ID liner is not interchangeable with a 6″ appliance collar without an adapter, and too many previous installations used exactly that bodge. A 5.5″ liner jammed onto a 6″ stove outlet creates a choke point that accelerates creosote buildup and burns out the liner in half the normal lifespan. When we inspect Flushing chimneys with Olympia-branded components, we always verify the liner ID against the appliance spec before quoting a replacement. If you’re matching an existing Olympia liner, the ID is the number that matters most.

On OEM versus aftermarket: Olympia’s own liners are solid, but the honest truth is that a quality 316L or 904L stainless liner from DuraFlex or HeatShield performs identically when sized correctly and is often $200 to $400 less for the part. We stock both, quote both, and let the homeowner decide. The warranty on the liner material itself comes from the manufacturer; the labor warranty is ours. We don’t pretend the brand name on the box changes how stainless steel behaves in a flue.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Smoke rolling back into the room. When a liner cracks or separates, the draft reverses on cold starts. You’ll notice it most on damp, windy Flushing days. The flue can’t pull air through itself properly, so smoke follows the path of least resistance, which is back through the fireplace opening.
• Rust stains or flaking metal at the cleanout door. If you have a cleanout at the base of the chimney, open it and look. Rust chips and thin metal flakes inside mean the liner is corroding from the inside out. Condensation is the culprit, and once 316 stainless starts to pit in a Flushing chimney that cycles hot-cold all winter, it doesn’t stop.
• Crumbling clay tile pieces in the firebox. If your Olympia liner was installed over an old clay tile system, the clay tiles eventually spall, they break apart, and pieces fall down. You’ll see chunks of terra cotta in the fireplace, sometimes mixed with pieces of the liner itself.
• Stove or fireplace suddenly burning differently. A new rumbling sound, trouble getting a fire to catch, or a stove that burns through wood twice as fast all point to a draft problem. A failed liner lets air in where it shouldn’t, which disrupts the burn and drops efficiency.
• Visible gaps at the liner seams. Olympia liners have a welded or mechanically locked seam running the length of the tube. When we run a camera and see the seam separating or a pinhole of daylight through it, that liner is done. It’s a structural issue, not something that patches.

Before

After

Replacement Cost & What’s Included

Here’s the Flushing pricing reality, in writing:

• Single-story home, 15-25 ft flue: $2,400-$3,200 installed
• Two-story home, 25-40 ft flue: $3,200-$4,200 installed
• Three-story or steep-roof Flushing home, 40+ ft flue: $4,200-$4,800 installed
• 904L alloy upgrade (for oil-fired appliances or high-condensation flues): add $400-$700

The range is driven by flue height, roof access, liner diameter, and whether insulation wrap is required, which it usually is for exterior chimneys common in Flushing attached homes. Every quote is written before work starts. It itemizes the liner part number, the length, the alloy grade, the insulation, and the labor. You’ll see the price, and that’s the price. No surprises after the fact. Every replacement includes a before-and-after camera scan, photos you keep, and a written warranty on our work, backed by the 365-Day Done Right Promise.

DIY or Call Us?

A flue liner replacement is roof work. It’s not a flip-the-breaker job. You’re on a Flushing roof, often steep, often shared with an attached neighbor, pulling a 30-foot stainless tube out of a brick chimney. If the old liner is seized or the crown needs rebuilding at the same time, which it usually does by the time the liner fails, you’ve got masonry work on top of the liner work. This is not a weekend project, and it’s high enough off the ground that a mistake isn’t a scrape, it’s a hospital trip.

What you can safely do: check the cleanout door for rust chips, look for clay tile fragments in the firebox, and note whether the smoking gets worse on windy days. Those observations help us quote faster. The actual removal and reline, we’d rather you not attempt from a ladder. Call us at (516) 240-9191. We’ll run the camera, show you the footage, and give you a written price. If you’re not sure whether the liner even needs replacing, the camera answers that question in 20 minutes.

How long does an Olympia Chimney flue liner last in Flushing?

A properly installed 316L stainless flue liner lasts 15 to 25 years in Flushing’s climate, sometimes longer if the fireplace sees light use. 904L alloy runs 25 to 30 years. The Flushing-specific killer is condensation. Wet ocean air, cold winters, and a chimney that cycles hot to cold daily creates acidic condensation inside the liner, which eats stainless from the inside. Insulated liners last on the long end of that range. Uninsulated liners in exterior chimneys, the standard configuration for attached Flushing rowhouses, last on the short end. Call (516) 240-9191 and we’ll look at what’s actually in your flue.

Can a damaged Olympia flue liner be repaired instead of replaced?

Small pinholes and minor seam gaps can sometimes be addressed with a resurfacing product like HeatShield, which we install as an alternative when the liner’s structural integrity is still sound. But if the liner has separated at the seam, is rusted through in multiple places, or has collapsed, there’s nothing to resurface. A patch over a failing stainless liner doesn’t work; the patch becomes a hot spot and fails within a season or two. Corrine Halstead never recommends resurfacing over a liner that the camera shows is compromised. We’d rather tell you the liner can wait another year than sell you a repair that won’t hold.

How long does a flue liner replacement take?

Most Olympia flue liner replacements in Flushing take four to six hours from setup to final camera scan. That includes removing the old liner, prepping the flue, dropping in the new liner, connecting it to the appliance, and running the camera to document the finished work. Steeper roofs, difficult access, or a crown that needs rebuilding at the same time can push the job into a second day. We’ll tell you the expected timeframe in the written quote before you commit.

Do you stock Olympia Chimney flue liners on the truck?

Yes. We carry Olympia Chimney-compatible 5.5″, 6″, and 8″ liners in both 316L and 904L as standard truck stock when we’re doing Flushing jobs. That means most replacements happen the same day we quote, no waiting on a distributor. If you need a size we don’t have, which is rare for residential Flushing flues, we source through Haven’s buying network from DuraFlex, HeatShield, or Gelco and typically have it within two business days. Call (516) 240-9191 for a free estimate, or bring us a competitor’s written quote for a free second opinion.

Written by Corrine Halstead, Owner, Level Two Chimney Flushing at Level Two Chimney Flushing, serving Flushing and nearby areas.